HUBA

699 Series Differential Pressure Indicator & Transmitter

Field Selectable Voltage and Current Outputs, F.S. Ranges From 0.1 to 20"

DESCRIPTION

Series 699 measures low differential pressures typically found in air conditioning applications such as air flow measurement, fan static pressures and specialty room pressure measurements in clean rooms and other low pressure space monitoring applications.

The 699 series incorporates time proven ceramic fulcrum lever technology. They deliver adjusted and temperature-compensated sensor signals, available as standard voltage or current outputs.

The 699 is available in three configurations offering different levels of function and cost.

Configuration 1 is a transmitter with field selectable ranges and factory preset output signal and zero offset configurations.

Configuration 2 incorporates a 10 position DIP switch allowing field selection of range, output signal & response time. A potentiometer allows further adjustment of span within the selected range.

Configuration 3 incorporates an LED display and full field function programming via programming button including setting of range and fine tuning of span, output signal, zero offset, units of measurement, response time, square root extraction and display light settings.

SPECIFICATIONS

Medium: Air and neutral gases
Pressure ranges: F.S. from ± 0.1 to 20" w.c. See order table for field selectable ranges 
	offered for each model
Units of pressure measurement: Inches w.c., mm w.c.
Tolerable overload on one side of diaphragm:
	Pressure: 40" w.c. at P1, 1.6" w.c. at P2
	Vacuum: 40" w.c. at P2, 1.6" w.c. at P1
Rupture pressure:
	2 x overload at ambient temperature
	1.5 x overload at 70°C
Zero Adjustment: Zero point resettable by reset button
Materials in contact with medium:
	Housing: Polycarbonate PC
	Diaphragm: Silicone
	Sensor: Al2O3 (96%) / glass
Temperature:
	Medium and ambient: 32 to 158°F (0 to +70°C)
	Storage: 14 to 158°F (10 to +70°C)
	No condensation
Output/Power Supply:
Three-Wire
	0 to10 V, 13.5to 33 VDC / 24 VAC ±15%
	0 to 20 mA, 13.5 to 33 VDC / 24 VAC ±15%
	4 to 20 mA, 13.5 to 33 VDC / 24 VAC ±15%
Two-Wire
	4 to 20 mA, 8.0 to 33 VDC
	Additional adjustable by software (with LCD Display, configuration 3 only): 
	0-5.0V, 6.5 to 33 VDC / 24 VAC ±15%
Load:
3-wire:
	0-10 V > 10 kOhm
	0-20 mA < 500 Ohm
	4-20 mA < 500 Ohm
2-wire:
	4-20 mA < (supply voltage - 8V) ÷ (0.02 A)  Ohms
Current Consumption:
3-wire:
	0-10 V < 10 mA
	0-20 mA < 30 mA
	4-20 mA < 30 mA
2-wire
	4-20 mA 20 mA
	Backlight LCD-Display: 30 mA
Dynamic response:
	Response time: < 20 ms
	Load cycle: <10 Hz
Response time Filter: Filter response time switchable for configuration 2: off or 1 second 
	Filter response time programmable for configuration 3: 0.2 / 1 / 5 / 20 seconds
Electrical connection: Screw terminals for wire and stranded conductors up to 16 AWG, 
	PG11 cable gland with built-in strain relief
Polarity reversal protection: Short circuit proof and protected against polarity reversal. 
	Each connection is protected against crossover up to max. supply voltage.
Protection standard:
	Without cover: IP 100
	With cover: IP 54 or IP 65
Pressure connections:
	Hose barb: .244" (6.2 mm)
Installation: Recommended and factory adjustment vertical, with pressure connections downward
Mounting: Mounting bracket (integrated in case)
Display,configuration 3: LCD display, double spaced per 8 digit alphanumeric (3-wire with backlight)
Tests: CE conform
Weight:
	With Display: approx.100 g
	Without Display: 90 g
Packaging: Individually boxed

Cross-section Drawing Legend
1	Diaphragm
2	Sensor element
3	P1(Higher Pressure) Pressure connection
4	LCD-Display (option)
5	Amplification Circuit
6	Connection terminals
7	Cover
8	P2 (Lower Pressure) Pressure connection

Accuracy
	0.2" w.c	0.4 " w.c.	1.2 " w.c.	2.0 " w.c.	4 to 20" w.c.
Tolerance zero point (max.).	±1.0% fs	±1.0% fs	±0.7% fs	±0.7% fs	±0.7% fs
Tolerance full scale	±1.0% fs	±1.0% fs	±0.7% fs	±0.7% fs	±0.7% fs
Resolution	±0.2% fs	±0.2% fs	±0.1% fs	±0.1% fs	±0.1% fs
Total of linearity, hysteresis and repeatability (max.)	±1.0% fs	±1.0% fs	±1.0% fs	±1.0% fs	±0.6% fs
Long therm stability acc. to DIN IEC 60770	±1.0% fs	±1.0% fs	±1.0% fs	±1.0% fs	±1.0% fs
Temp. Coeff. zero point (typ.)	±0.2% fs/10K	±0.2% fs/10K	±0.2% fs/10K	±0.1% fs/10K	±0.1% fs/10K
TC Temp. Coeff. zero point (max.)	±1.0% fs/10K	±1.0% fs/10K	±0.5% fs/10K	±0.4% fs/10K	±0.4% fs/10K
Temp. Coeff. sensitivity (typ.)	±0.3% fs/10K	±0.3% fs/10K	±0.2% fs/10K	±0.1% fs/10K	±0.1% fs/10K
Temp. Coeff. sensitivity (max.)	±0.6% fs/10K	±0.6% fs/10K	±0.5% fs/10K	±0.5% fs/10K	±0.2% fs/10K
Test conditions: 25°C, 45%RH, Power Supply 24 VDC; Temperature Coefficient Zero Point 32 to 158°F (0 … 70°C)

Legend
1	Dual DIP Switch
1a	10 Position DIP Switch
2	Zero Point Reset
3	Terminal Connection
4	P1 & P2 Pressure Ports
5	Signal Amplification Potentiometer
6	LCD
7	LCD Receptacle

Configuration Major Differences
Parameter	Config. 1	Config. 2	Config. 3
LCD Display	No	No	Yes
Field Select Output Signals	No	Yes	Yes
Field Select Response Time	No	Std. or 1 sec.	0.2, 1, 5 or 20 sec.
Display Program Menu & Program Button	No	No	Yes

ORDERING INFORMATION

ORDER NUMBER ABCDEFGHI
EXAMPLE: 6999-11321113