Panel Mount Tachometer Sensors and Output Modules

Panel Mount Tachometer Sensors and Output Modules
Accessories for Models DT-5TG & DT-5RL

OUTPUT MODULES FOR MODEL DT-5TG

DOP-FV Module (0 - 10VDC, 4 - 20mA DC Output) This unit provides analog output (voltage or current) proportional to the input signal frequency. A microprocessor and 12-bit A/D converter provides full span analog output regardless of input signal range.
Weighs 3.5 oz (100 g).

DOP-CP Module (Set Points)
The DOP-CP uses three independent relays that work in conjunction with the display functions "HI", "GO", and "LO" of the DT-5TG. It also features a currentsinking transistor, which is activated when the monitored
rate reaches zero.
Weighs 3.5 oz (100 g).

DOP-RM Module (Ratio Input)
Allows the DT-5TG to be used as a ratio meter; it measures and displays in percent, absolute ratio of two rate functions (B/A), dispersion ratio (B/A-1) and the difference of the two rates (B-A).
Weighs 3.5 oz (100g).

Output Modules For Model DT-5TG

DOP-SD Module (RS232C Output)
Provides an RS232C/MTI output signal for long line transmission and processing with the DT-5TG. The baud rate, parity and data bit lengths are adjustable to fit any electronic device capable of accepting RS232C signals. For statistical analysis this module can be interfaced with Mitutoyo's Digimatic processors.
Weighs 3.5 oz (100 g).

SENSORS PLEASE CALL 1-800-253-2497 TO ORDER THESE ITEMS *PROXIMITY SENSORS*
B12-S12 The BI2-S12 is a 3 wire DC inductive proximity sensor. Features include short circuit, overload protection and output LED. Meets NEMA ratings 1, 3, 4, 6, 13, and IEC IP67.
SE-G A solid state 3 wire proximity (switching) sensor specially designed for gear sensing. Provides a square wave output signal and indicates detection via LED indicator (gear pitch must be between 16.93 and 25.4).
MCS-3109 Complimentary (NPN-NO and NPN-NC) proximity sensor normally used in high-vibration areas and where a greater sensing distance is required.
*MAGNETIC PICK-UP SENSORS*
MP-10 Magnetic Pick-Up Sensor General-purpose economy model. The unit is designed to mount in a 5/8"-18 threaded hole with included securing jam nut. 10 foot cable included.
3030AN Magnetic Pick-Up Sensor Magnetic pick-up with Amphenol connector; requires sensor cable assembly. This general-purpose unit is designed to mount in a 5/8"-18 threaded hole and is provided with a jam nut for sensor securing.
3070A Magnetic Pick-Up Sensor Specifically engineered for use in the oil and petrochemical industries, this stainless steel sensor is completely sealed and explosion-proof. Low impedance allows for transistor circuit input. When mated with conduit, it provides positive protection against damage due to water, high humidity, oil, dirt, dust, or corrosive liquids. UL and CSA listed for Class I-Group C & D hazardous locations. Class II-Group E, F, & G.
*MEASURING SENSORS*
LSL-3 Series Linear Speed and Length Measuring Sensors This series of continuous-use compact steel sensors (in conjunction with the proper meter or counter) measure length in meters, yards and rate in different engineering units by changing only the wheel assembly.
*RETRO-REFLECTIVE SENSORS*
RS-220HR Retro-Reflective Sensor A general purpose sensor, featuring an operating range up to 500Hz. Consists of an LED infrared light source sensing device and amplifier contained in a heavy-duty housing. Includes an indicator lamp for initial alignment purposes.
MCS-625 Retro-Reflective Sensor The MCS-625 consists of an LED infra-red light source sensing device and amplifier contained in a heavy-duty housing. For initial alignment purposes, a small indicator lamp is mounted in the top of the sensor housing. The MCS-625 has an open collector output and requires a pull up resistor.
MCS-655 Retro-Reflective Sensor Incorporates a complimentary switching voltage output (light/dark activated) that operates up to 333Hz. An LED is mounted in the back of the unit with sensitivity adjustment for alignment purposes.
*ROTARY PULSE GENERATORS*
RE1B-60C Rotary Pulse Generator 60 digital output pulses per shaft revolution. Maximum speed: 5000 RPM
RE1B-600C Rotary Pulse Generator 600 digital output pulses per shaft revolution. Maximum speed: 3000 RPM
RE1B-1000C Rotary Pulse Generator1000 digital output pulses per shaft revolution. Maximum speed: 1800 RPM
RE2B-30C, RE2B-60C, RE2B-600C Rotary Pulse Generators Dual (90° out of phase) digital pulses for quadrature applications. Also a zero position (third output) is available to mark the reference position of the shaft. Maximum speed: 3000 RPM and 5000 RPM, respectively.

For assistance call 978-568-3400