| PLEASE CALL 1-800-253-2497 TO ORDER THESE ITEMS |
| ATTACHMENT |
CAPACITY |
DESCRIPTION |
|
| Small Pin Grips |
| FG-M4PIN05 |
22 lb (11 kg) |
Ideal for gripping fine wires and filaments; three ranges for checking samples of .02", .04", .08" (0.5, 1 and 2 mm) thick. |
 |
| FG-M4PIN1 |
| FG-M4PIN2 |
| FG-M6PIN05 |
| FG-M6PIN1 |
| FG-M6PIN2 |
| Fine Point Grips |
| FG-M4FPG3 |
30 lb (15 kg),
.12" (3mm) |
Perfect for testing fine and medium gauge wire, ribbon tape and paper. Two jaw widths and load capacities are available; both can handle material thickness up to .04" (1 mm). |
 |
| FG-M4FPG8 |
| FG-M6FPG3 |
60 lb (30 kg),
.31" (8mm) |
| FG-M6FPG8 |
| Film Grips |
| FG-M46FLM20 |
100 lb (50 kg) |
These heavy-duty, spring-loaded grips have serrated jaws for handling samples up to .39" (10 mm) thick and .79" (20 mm) or 1.97" (50 mm) wide. |
 |
| FG-M6FLM20 |
| FG-M6FLM50U |
FG-FLM50B
(test stand mount) |
| Jacob's Chuck Grips |
| FG-M6JAC5U |
100 lb (50 kg) |
Designed for testing low gauge wire and rigid rods; accepts material diameters from .02" (.05 mm) to .20" (5 mm). |
 |
FG-JAC5B
(test stand mount) |
| Flat Chuck Tensile Grips |
| FG-M6FTG20U |
100 lb (50 kg) |
Each serrated gripping face is .79" (20 mm) square and can accept samples up to .79" (20 mm) thick. |
 |
FG-FTG20B
(test stand mount) |
| Spool Grips |
| FG-M6SP010U |
100 lb (50 kg) |
Ideal for hard-to-hold items like thread, filaments,etc. The sample is wrapped around the spool, anchored by friction. |
 |
FG-SPO10B
(test stand mount) |
| Tape Grips |
| FG-M6TAP30U |
100 lb (50 kg) |
Self tightening lever action makes this fixture perfect for testing rubber, tape and paper. |
 |
FG-TAP30B
(test stand mount) |
| Wedge Grips |
| FG-M6WDG50U |
100 lb (50 kg) |
Two capacities for lighter and heavier loads; spring loaded jaws automatically close on the specimen and tighten as tension is applied. Ideal for testing wires, strip material and plastic tape or films. |
 |
| FG-M10WDG500U |
500 lb (250kg) |
| Heavy-Duty Tensile Grip |
| FG-M10TEN7U |
500 lb (250 kg) |
Manually tightened jaw faces can accept samples 1.25" (31.75 mm) wide and .25" (6.35 mm) thick. Contact faces are serrated hardened tool steel. |
 |
FG-TEN7B
(test stand mount) |
| Clevis Grips |
| FG-M10CLV10U |
500 lb (250 kg) |
Odd shaped parts, punched samples or tension springs are easily secured and tested. Concave shape to pins assures centering under load. Throat clearance with pin is .5" (12.7 mm) and can easily accept samples up to .375" (9.65 mm) wide. |
 |
FG-CLV10B
(test stand mount) |
| Cord and Twine Grips |
| FG-M10TWN500U |
500 lb (250 kg) |
A unique figure 8 wrap of specimen assures a center break and non locking pins permit quick installation and release. Throat and pin clearance is .375" (9.65 mm) wide with the throat width being .5" (12.7 mm). |
 |
FG-TWN500B
(test stand mount) |
| Fabric Grips |
| FG-M10FAB80U |
500 lb (250 kg) |
Eccentrically mounted, serrated roller grips allow for self tightening of specimens up to 3" (76.20 mm) wide and .25" (6.4 mm) thick. |
 |
FG-FAB80B
(test stand mount) |
| Adhesive Test Plates |
| FG-M10ADHE3 |
100 lb (50 kg) |
Samples up to 3" (76.20 mm) in diameter can be tested with hardened tool steel detachable faceplates. Ball socket mounting screws in both grips assure parallelism and perpendicularity to force when load is applied. |
 |
| Wire Terminal Test Fixture |
| FG-M6WTER100 |
100 lb (50 kg) |
Designed specifically to test the strength of wire/terminal connections. The upper grip consists of a self-aligning wheel with nine equally spaced slots of various terminal shank sizes; an eccentrically mounted, self-tightening bottom grip secures the wire on the other end. |
 |
| Compression Plates |
| FG-M6COMP50U |
100 lb (50 kg) |
Hardened compression plates available. 50mm and 100mm available in M6 and M10 threads. |
|
| FGM6COMP100U |
500 lb (250 kg) |
